Avalanche Heavy Duty UNIVERSAL T-Frame snow plow Kit. Includes 3000lb Upgraded winch (EW8020) and Upgraded wireless remote (EWX004)
The DK2 Avalanche Snow Plow kits combine the simplicity of our original T-Frame plow with the strength of our custom mount frame.
The DK2 Avalanche Snow Plow allows you to quickly and effectively remove snow from your driveway or small parking lot.
The Avalanche simply slides into a 2” front mount receiver for easy removal and storage.
Each snow plow ships in a single carton complete with hardened steel cutting edge scraper, rubber snow deflector, polymer-wrapped wire rope plow markers, skid shoes, castor kit for easy storage, and a 3,000lb wireless electric winch. Each Avalanche plow will also include a set of blade stiffeners for added strength by creating a 3 point connection.
5. Manual lever allows blade to angle left or right. 6. Vehicle specific custom mounting brackets. 7. All steel adjustable skid shoes let you control the height of the scrape. 8. Flip down castors allow easy plow attachment, removal, and roll away storage.
Converting any Generation 1 (grey) DK2 snow plow kit over to a custom mounting system is as easy as changing out the winch tower and T-frame (NO 17) for a mainframe and a custom mounting brackets.
The benefits of switching over to a custom mount is adding strength to your snow plow by shortening the frame by nearly 14 inches. We are happy to chat with customers further about changing their generation 1 plow over to a custom mount plow.
List of items needed:
MAIN FRAME CUSTOM MOUNT BRACKETS CROSS MEMBER HANDLE*
*The existing handle can be cut down by the competent DIY'er to work with the new frame components.
It is important to check all nuts and bolts and ensure they are tight before you plow. You can put dielectric grease on the grey quick connection to avoid electrical issues.
If you winch pin is bent it means you had the strap going over top of the pin the wrong way. You can call DK2 at 1-888-277-6960 to order a new one.
LB is the light kit for our first generation snow plows (the grey blades) and LB2 is the light kit for our second generation snow plows (the black blades).
This is a very common mistake customers make during assembly. The middle section of the scraper blade is the longest piece and the two short ones go on the ends. If they aren’t lining up try flipping the scraper blade over.
The 35 AMP circuit breaker is necessary to prevent possible electrical damage to either the winch or the vehicle’s electrical system. You connect it to the red wire going from the control box to the battery.
Our snow plows are designed to minimize the wear and tear on your vehicle. The fact that you can remove your snow plow whenever you aren’t plowing dramatically cuts down on the stress a plow can have on your vehicle frame.
The T-frame style snow plows (Avalanche Series) mount on to any vehicle with a standard 2” class III front mount receiver. The custom mount snow plows (Summit II, Rampage II, Storm II) use a set of vehicle specific mounting brackets joined by a cross member which connects the plow frame to the frame of your vehicle.
First thing you should do is double check you have the proper custom mount for your vehicle. You can check our mount guide under the custom mount section of our website. It is also important to loosely install both left and right mounting brackets first. Then loosely install the cross member between the left and right bracket. Go back and tighten left and right bracket then finally the cross member should be tightened into place.
Yes you can drive on the streets with the snow plow attached to your vehicle. It is always important make sure the safety clips or the hitch pin are secured and your plow is safely mounted to your vehicle. Use the safety chain while you aren’t plowing to take stress off your winch strap.
The operator of the plow can decide how high to set the skid shoes. We recommend setting them about 1/4 of an inch below the scraper blade. The skid shoes will help protect the surface you are plowing and also prevent wear on your scraper blade.
Yes you can drive on the highway with your plow but we do not recommend driving far distances with the plow on the front of your vehicle. If you are driving with the blade on make sure to angle the blade to the left or right.
If you hear a clicking there is a good chance your winch relay (black control box) isn’t working. You can check that your winch is fine by hooking up a power source directly to the winch and by pass the control box. If the winch works fine you need a new WCB (winch control box).
If your winch isn’t working properly the first thing to check is the connections in the grey or blue quick connect piece. If there is any corrosion in here it can affect the operation of the winch.
The first thing to check is the battery in your wireless remote. If you have replaced the battery and the wireless still isn’t working try plugging your wired remote into the control box and make sure it isn’t a winch problem and is in fact your wireless.